You are currently viewing our boards as a guest, which gives you limited access to view most discussions and access our other features. By joining our free community, you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content, and access many other special features. In addition, registered members also see less advertisements. Registration is fast, simple, and absolutely free, so please, join our community today!
Post subject: burrs for voided and resized photos.....
Posted: Sat Aug 27, 2011 12:01 am
Forum Member
Joined: Sat May 14, 2011 1:17 am Posts: 60 Location: canada
I could of been more careful sanding down the fender but I sorta rushed it towards the end. during the winter It will come apart and over many coffee I will fine tune and clean er up. I flipped the license plate bracket so the plate wouldn't lean under the bike and attached the turn signals right to that bracket with the aid of some washers while I waited for my led. if you aren't using a led then drill two small holes to run the wires under the fender to hide them better...I didn't use that saw to cut the windscreen neither. I use a hacksaw that didn't have a backbone. and resized the pics cause someone asked and I actually had no idea that were going to be that big!
Attachments:
fenrear.jpg [ 69.62 KiB | Viewed 290 times ]
fen.jpg [ 65.03 KiB | Viewed 290 times ]
burrs.jpg [ 48.21 KiB | Viewed 290 times ]
_________________ yosh trc, xtre, led tail light, PR2's, black oem levers,
Post subject: Re: burrs for voided and resized photos.....
Posted: Sat Aug 27, 2011 12:07 am
Forum Member
Joined: Sat May 14, 2011 1:17 am Posts: 60 Location: canada
and thats thats! I've looked a dermel a 1000 times now and never ever buy it! but alass over winter to mess with the fender I will buy me a new power tool. note: the plastic clips "four of them" that hold the under tail on break super easy!!! I busted two and I was being gental.
Attachments:
ugly.jpg [ 54.78 KiB | Viewed 287 times ]
signal.jpg [ 97.48 KiB | Viewed 287 times ]
screen.jpg [ 72.53 KiB | Viewed 287 times ]
_________________ yosh trc, xtre, led tail light, PR2's, black oem levers,
Post subject: Re: burrs for voided and resized photos.....
Posted: Sat Aug 27, 2011 1:36 am
Forum Member
Joined: Sat May 14, 2011 1:17 am Posts: 60 Location: canada
next project is to cut my stock mirrors. I'm gonna cut the stem roughly in half so they don't stick out as far. grind the end so that it fits into the bracket and drill the hole! I'm gonna tape up the glass in hopes that it don't bust from vibration. not sure if I'll have any luck with this but I can't seem to find anything that I like. If it fails I'll order a nudder set of oem's maybe...
_________________ yosh trc, xtre, led tail light, PR2's, black oem levers,
Post subject: Re: burrs for voided and resized photos.....
Posted: Sat Aug 27, 2011 10:20 am
Forum Member
Joined: Mon Jun 21, 2010 9:09 am Posts: 637 Location: Bucyrus, Ohio
hey starr? I cannot recommend you do that. I've never had a mirror work after Breaking it, letting alone doing a clean cut. if you glue it, even 130 mph wind will send it packing. I guarentee it.
I bumped a mirror with my elbow and broke it. reglued it, and it broke again in an hour. they're worthless if you mess with em.
Users browsing this forum: No registered users and 0 guests
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum
